Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work such as translation, Campus Drive transformation, or adaptation without written permission from 3Com Technologies.
|Published (Last):||19 February 2006|
|PDF File Size:||19.81 Mb|
|ePub File Size:||2.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. Table of Contents. Switch 3Com Getting Started Switch series 74 pages. Page 2 Environmental Statement It is a 3Com policy to be environmentally friendly in all operations. This manual is printed on paper that comes from sustainable, managed European forests. The production process for making the pulp has a reduced AOX level adsorbable organic halogen resulting in elemental chlorine-free paper.
Page 9: Related Documentation SuperStack 3 Switch Implementation Guide This guide contains information on the features supported by your Switch and how they can be used to optimize your network. Documentation accompanying 3Com Network Supervisor.
Table 3 Hardware features Redundant Power To protect against internal power supply failure, you can use this socket Page Package Contents Water or moisture cannot enter the case of the Switch. Air-flow is not restricted around the Switch or through the vents in the side of the Switch. Air temperature around the Switch does not exceed 40 The air is as free from dust as possible. Page Rack-Mounting To rack-mount your Switch: 1 Place the Switch the right way up on a hard flat surface, with the front facing towards you.
Switch Family 1 Plug the power cord into the power socket at the rear of the Switch. If a Unit LED is off, initialization is not complete. See 3Com recommends that you use Category 5 twisted pair cable — the maximum segment length for this type of cable is m ft.
Use the following sequence of steps to activate the GBIC ports. Page 29 SC connector on the transceiver. However, to make full use of the features offered by the Switch, and to change and monitor the way it works, you have to access the management software that resides on the Switch. The whole setup process is summarised in are contained in the sections that follow. For most installations, 3Com recommends that you configure the Switch IP information manually.
You must do this whilst the Switch is offline, that is, before you connect the Switch to a network. You can do this using the Web interface or the command line interface CLI via telnet. Using the Web Interface 1 Power-up the Switch.
Page 37 The final page displays a summary of the information entered. The initial set up of your Switch is now complete and the Switch is ready for you to set up your chosen management method. The screen displays a summary of the information entered. This software allows you to communicate with the Switch via the console port directly, or through a modem. Documentation supplied with the terminal emulation software. Connecting to the Page 43 1 Connect the workstation to the console port using a standard null modem cable as shown in Figure 13 Connecting a workstation to the Switch via the console port To connect the cable: a Attach the female connector on the cable to the male connector on the console port of the Switch.
Page 44 You are now ready to view the automatically allocated IP information using the command line interface. As soon as a network connection is made the Switch begins the automatic IP configuration process. Make a note of the Network IP Address. For example, you can use the 3Com Network Supervisor Switch page Page Setting Up Command Line Interface Management To manage a Switch using the command line interface over a network the Network using Telnet: 1 Ensure you have already set up the Switch with IP information as described in 2 Check that you have the IP protocol correctly installed on your management workstation.
Page Setting Up Web Interface Management If the login prompt does not display immediately, press Return a few times until it starts.
Page Pre-Requisites Passwords command line interface, or to change the default passwords, you need to log in with a valid user name and password. The Switch has three default user names, and each user name has a different password and level of access. There is also an explanation of IP addressing. Page Solving Stack Formation Problems If your IP network is internal to your organization only, that is, you do not access the Internet, you may use any arbitrary IP address as long as it is not being used by another device on your network.
X where X is a number between 1 and with a subnet mask of Page A Safety Information You must read the following safety information before carrying out any installation or removal of components, or any maintenance procedures on the Switch Series.
Follow all directions carefully. These are shielded RJ data sockets. They cannot be used as standard traditional telephone sockets, or to connect the unit to a traditional PBX or public telephone network. Operational testing: paras 2. If your These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This manual is also suitable for: Superstack g Superstack t 3ca Superstack 3 t Superstack 3 t Superstack 3 g Show all Superstack 3 3c Superstack 3 3c Superstack 3 3c 3c 3c 3c Print page 1 Print document 84 pages.
Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
3Com 4226T - SuperStack 3 Switch Manuals
All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work such as translation, transformation, or adaptation without written permission from 3Com Technologies. Examples: From the Help menu, select Contents. Click OK. These are shielded RJ data sockets. They cannot be used as standard traditional telephone sockets, or to connect the unit to a traditional PBX or public telephone network. Only connect RJ data connectors, network telephony systems, or network telephones to these sockets.
3com SuperStack® 3 Switch 4226T 24-Port 3C17300-ME Data Sheet
3Com SUPERSTACK 4226T user manual